Microsonic nano-15/CI Manuel d'utilisateur télécharger pdf

Operating instructions

Ultrasonic sensor with one

analogue output

nano-15/CI nano-15/CU

nano-24/CI nano-24/CU

Product Description

The nano sensor offers a non-contact

measurement of the distance to an

object that has to be present within

the sensor’s detection zone. Depend-

ing on the set window limits, a dis-

tance-proportional analogue signal is

output.

The window limits of the analogue

output and its characteristic can be

adjusted with the Teach-in proce-

dure.

One 2-colour LED indicates operation

and the state of the analogue

output.

Sensor adjustment with Teach-in procedure

Set window

margins

Place object at position .

Connect Teach-in for about

3 s to +U

, until LED

flashes yellow.

LED:

Place object at position .

flashes green/yellow

Set rising/falling output

characteristic curve

Connect Teach-in for about

13 s to +U

, until LED

flashes green/yellow

alternately.

LED flashes:

green, green/

yellow:

rising,

green:

falling charac-

teristic curve

Reset to factory setting

Switch off power supply.

Connect Teach-in to +U

Switch on power supply.

Keep Teach-in connected to

for about 13 s,

until LED flashes

green/yellow alternately.

Disconnect Teach-in from

within 5 s before

switching off power supply.

Connect Teach-in for about

1 s to +U

Normal operating mode

To change output charac-

teristic connect Teach-in for

about 1 s to +U

Wait for about 10 s.

Normal operating mode

Safety Notes

 Read the operating instructions

prior to start-up.

 Connection, installation and

adjustment works should be car-

ried out by expert personnel only.

 No safety component in

accordance with the EU Machine

Directive

Use for intended purpose only

nano ultrasonic sensors are used for

non-contact detection of objects.

Installation

 Mount the sensor at the installa-

tion site.

 Connect a connection cable to the

M12 device plug.

The assembly distances shown in fig.

2 for two or more sensors should not

be fallen below in order to avoid mu-

tual interference.

Fig. 1: Pin assignment with view onto sensor

plug and colour coding of the

microsonic connection cable

colour

-U

brown

blue

I|U

Teach-in

black

white

Start-Up

 Connect the power supply.

 Carry out the sensor adjustment in

accordance with the diagram.

Fig.2: Assembly distances, indicating syn-

chronization

≥0,25 m

≥0.25 m

≥1.3 m

≥1.4 m

Factory Setting

 Rising analogue characteristic

curve between the blind zone and

the operating range

Maintenance

microsonic sensors are maintenance-

free. In case of excess caked-on dirt

we recommend to clean the white

sensor surface.

Notes

 Every time the power supply is

switched on, the sensor detects its

actual operating temperature and

transmits it to the internal tempe-

rature compensation. This results

in a slight correction of the ana-

logue output value after 45 se-

conds.

 If the sensor was switched off for

at least 30 minutes and after po-

wer on an object is placed in the

middle of the adjusted analogue

window for 30 minutes (the ana-

logue output value is in the range

of 11 to 13 mA or 4.4 to 5.6 V) a

new adjustment of the internal

temperature compensation to the

actual mounting conditions takes

place.

 The sensors of the nano family

have a blind zone. Within this

zone a distance measurement is

not possible.

 In the normal operating mode, an il-

luminated yellow LED signals the ob-

ject is within the adjusted window

limits.

 The sensor can be reset to its fac-

tory setting (see »Further set-

tings«).

Ultrasonic Sensors

Set analogue output

Further settings

2004/108/EC

1 2

Ultrasonic Sensors 1
*B10707* 2

Résumé du contenu

Page 1 - Ultrasonic Sensors

Operating instructionsUltrasonic sensor with one analogue outputnano-15/CI nano-15/CUnano-24/CI nano-24/CUProduct DescriptionThe nano sensor offers a

Page 2 - *B10707*

Technical datablind zoneoperating rangemaximum rangeangle of beam spread20 mm150 mm40 mm240 mm250 mmSee detection zone350 mmSee detection zonetransduc

Modèles reliés nano-24/CI | nano-15/CU | nano-24/CU |

Commentaires sur ces manuels

Pas de commentaire

Microsonic nano-15/CI Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Capteurs Microsonic nano-15/CI. Microsonic nano-15/CI User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés nano-24/CI | nano-15/CU | nano-24/CU |

Commentaires sur ces manuels

Produits connexes et manuels pour Capteurs Microsonic nano-15/CI